Liberon LW250 250ml Liming Wax

Product Information

When water touches wood, especially wood that has a lot of open pores, like Red Oak, it will raise the grain. You heard me right, you can apply this over a piece that has not been stripped or sanded! You can go from an orangey oak finish to a limed oak wash finish in less than an hour! It’s almost too good to be true! Today’s post is showing you how I learned to dye wood and use liming wax (along with some tips for alternative white grain fillers). If you want a nice contrasting effect, use a dark stain to stain your pinewood. This step is optional, of course. If you already love the grain and color of your pinewood, you can skip this step.

Briwax Liming Wax is what I used. This stuff is amazing and wonderful! I tried it on two of the tables. One I sanded a bit and one I left with the glossy polyurethane finish. There is absolutely no reason to sand. After trying both, the one I sanded looks no better than the one I left with the glossy finish. Actually, it seemed to settle into the grain better on the one I didn’t sand. How To DIY a Limed Oak Table Apply Over Polyurethane

STEP 3: Sand the Wood With 150-grit Sandpaper

Remember, the goal is to open the grain without damaging the wood, so be gentle when you sand, especially when using a wire brush or coarse sandpaper. Achieving the best possible result with liming wax requires careful attention to these details. Where to Buy Real Milk Paint’s High-Quality Finishing Waxes And those turned legs…I don’t even know how I am supposed to get that off! Not my cup of tea at all! So, the little table that I experimented on still sits looking sad and halfway stripped. I loathe it and I don’t want to mess with it. Eventually I will finish it, but not today. Let’s Try Something Easy!! A Limed Oak Table Dyes look best on unfinished wood. Not that I’ve used them enough to know first hand, but from my research, I’ve learned that wood dyes work best on unfinished bare wood because they’ve not been contaminated with anything else. This could be good for small projects you might make, picture frames, DIY wooden journals, or any other wood craft or DIY project you make. I remembered I had half a container of Citristrip furniture stripper and some liming wax in the garage leftover from our wine cooler project. Why not try the bleached wood look again?

I’ve been looking for a way to tone down the orange finish of pine and now I’ve found the answer– Liming Wax! At this stage I can still play about with it, so I’m going to take a little bit of Clear Wax and maybe just try along the edge, and that will just take it… it’s like an eraser: it rubs it away. And it might just make it more apparent. I could just do the edge there and keep this bit whiter. Dyeing wood has been around for ages, but it’s new to me. As a DIY furniture painter, my experience with wood has been pretty limited. Who needed to know about wood when all you’re doing is painting it, right??I am personally so pleased with the finish. It gives it more of that coastal or white washed look. Or maybe it’s a farmhouse look. I don’t know, but I like it! It fit’s my style a bit better. I love the turned legs and the wax settles nicely in there to give a bit more contrast. It’s not a huge difference but over those few days the liming wax had bleached away most of the interest in the piece. There was very little difference or variation, it was all kind of a flat hazy white that was far more beachy than what we were looking for. At this point I was not really excited. I had spent a lot of time designing and building this piece, got the exact finish I wanted only for it to slip through my fingers like the time I lost three legged race right at the end at Field Day in third grade. Pretty much the same amount of crying. I was frantically googling how to strip off wax and start over at this point, and really not looking forward to that.

For a successful application of liming wax, you’ll need a few tools: a soft cloth or brush, sandpaper, wire brush, and protective gear or gloves. Preparing your workspace with a well-ventilated area, and ensuring the wood is clean and bare, is crucial too. The Process of Applying Liming Wax Sand the table lightly.I gave the whole table top a light sanding with coarse sandpaper and then followed up with a fine grit. If you want to make sure your table is completely down to raw wood, you can use a palm sander to give it a deeper sanding (wear a dust mask!) This is during the first pass of Citristrip. This is the part where you’re wondering if you should have started this, haha! Keep going! I’m building a DIY bathroom vanity and I’ve done a gazillion sample boards just to finally figure out what technique and shade looks best! I’ve added something new to the blog: audio! Maybe you don’t have time to read the entire post, but you can sure listen, can’t you? Go ahead and try. 😉

Applying wax to a finish with a sealed topcoat is a bit different than waxing chalk or milk paint (if that’s been your main experience with wax). Instead of soaking into the paint, the wax sits on top of the surface. So you have to be careful not to apply too much wax as well as not wipe off all of theexcess. For a little change, I put together a video demo for y’all today! I hope it’s helpful to actually watch the process of applying the wax. There are several varieties of pinewood, with summerwood being the strongest and most reliable variety. Most varieties of pinewood have a closed, wavy grain and a reddish color that ages very well. If you are interested in using a liming wax on your pinewood, there are a few extra steps to help you achieve the best result. Step 1: Sanding

It looks reallllly white at first. I was not loving it at this point and wondering if I had made a mortal mistake. But….I did love how the liming wax looked in the grain and in the lines of the apron all around the table….. Along the way, I’ve been asked about whether I’ve ever tried the liming wax. I’ve seen nice pictures of oak bath vanities and entire kitchens when searching for liming wax, but I have yet to find any that show that they actually used liming wax and how it turned out.Coat the table with wood conditioner.This will help the stain to take evenly. You can apply it with a nylon brush or a lint-free rag. Let it set for 10 or 15 minutes, then wipe off any excess, and you are ready to stain! Use a UVprotective sealer if you’re not waxing. If you’re not highlighting the grain of the wood with liming wax (and you’re using a white grain filler or white paint) then be sure to use a UV protective top coat that can help protect the wood from fading. Liming is a traditional wood finishing technique that was once commonly used on floorboards, furniture, and beams. It enhances the wood’s natural grain with a white tint, giving it a lighter, aged, and weathered look. More importantly, it can extend the life expectancy of your timber without having to seal the wood. Anyhow, to prepare a sample board, get a long piece Red Oak from The Home Depot. It doesn’t have to be super wide. Just wide enough so you can easily work on it and see the pattern. If you were wanting to do this on a dining table, I would imagine you would want to put a poly finish of some sort over it. I think the daily wiping would eventually wear away the finish. Before After What Do You Think?